Guides

40 weight vs 60 weight embroidery thread: when to use each

By Sara Nelson · · 6 minute read

Use 40 weight thread for almost every machine embroidery job. Switch to 60 weight when lettering or detail gets too small for 40 weight to stay readable, which is block letters under about a quarter inch tall.

That is the whole decision for most shops. The rest of this guide is the why, the letter sizes, and what else changes when you thread up a 60.

What the weight number means

The number runs backwards from what most people expect. A bigger number is a thinner thread.

Wikipedia's article on thread) explains the most common system. The weight is the length of thread, in kilometers, that it takes to weigh 1 kilogram. So 40 kilometers of 40 weight thread weigh a kilogram. It takes 60 kilometers of 60 weight to weigh the same, because each meter is lighter and thinner.

The same article says these numbers do not tell you the actual width of the thread. Treat the weight as a way to compare threads in the same family. Do not treat it as a measurement.

40 weight is the standard

Madeira USA's thread overview says "the standard 40 weight thread is ideal for almost every design." Kimberbell's article on thread types and thread breaks says they use a 40 weight top thread for most projects.

My own records say the same. Every top thread in my thread log is a 40. Most of it is Madeira Polyneon 40, a polyester. A few colors are Madeira Classic Rayon 40. That covers left chest logos on polos, caps, appliqué sweatshirts, and towels. I have not needed a 60 on top yet.

If you are buying your first set of colors, buy 40 weight.

When to switch to 60 weight

Small lettering is the main reason. Fine detail inside a logo is the second.

AllStitch's page on embroidering with 60 weight thread puts numbers on it. With 40 weight, block letters need to be about 6 to 7 millimeters tall at the smallest. That is roughly a quarter inch. With 60 weight, the same page says block letters can go as small as 3 millimeters.

Madeira USA's overview gives the same 3 millimeter floor for both its Classic Rayon 60 and its Polyneon 60. A second AllStitch page on the advantages of 60 weight is more careful and says letters down to 4 millimeters. Plan on 4 millimeters until you have stitched a test.

So here is the rule I would use:

  • Letters a quarter inch tall or taller: 40 weight.
  • Letters from about 4 millimeters up to a quarter inch: 60 weight. Four millimeters is just over an eighth of an inch.
  • Letters smaller than that: tell the customer it will not read, then make the text bigger.

Where those small letters usually show up is in my guide to placement measurements. A name under a left chest logo or a line of text on a cap side is where you will hit this first.

Use both weights in one design

You do not have to pick one thread for the whole logo. Madeira's article on the benefits of fine threads recommends 40 weight for the big fill areas and 60 weight for the fine details and lettering.

That is the setup that makes sense on a multi-needle machine. The same Madeira article suggests giving one needle position over to a finer needle and the fine thread, often needle 15. On a 16-needle machine like my Melco Bravo, that leaves 15 needles for the 40 weight colors.

What changes in the design file

This is where the sources disagree, so test before you run a customer's piece.

AllStitch's 60 weight advantages page says to increase the density by about 25% because the thinner thread covers less. AllStitch's other 60 weight page also says to increase density. It adds that you should tell your digitizer which areas will sew in 60 weight so they can avoid fill there.

Madeira's fine-thread article reports a comparison where no digitizing changes were needed to switch from 40 to 60.

My read is that both can be true. Satin lettering may stitch fine as is. A fill area in 60 weight may show fabric through it. Stitch the file once on a scrap of the same fabric and look for gaps before you decide.

If you outsource digitizing, put the thread weight on the order form. My guide on whether to learn digitizing or outsource it covers what to send.

The needle changes with the thread

A thinner thread wants a thinner needle. AllStitch says to always use a size 65 needle with 60 weight. Madeira USA suggests a 65/9 or a 70/10 for its 60 weight lines.

My guide to needle sizes covers what those numbers mean and when to switch.

AllStitch's 60 weight advantages page also says to slow the machine down slightly for small lettering.

Which weight goes in the bobbin

The bobbin is thinner than the top thread. Kimberbell uses a 60 or 90 weight bobbin thread, depending on the machine, under a 40 weight top thread.

My setup sheets list a 60 weight white polyester bobbin.

Kimberbell adds one warning for small lettering. With a 40 weight top thread over a 90 weight bobbin, the bobbin thread can come up through the stitches. If white specks show up in small dark letters, check the bobbin before you blame the file. Your machine's manual has the final word on which bobbin weight it takes.

Does 60 weight change the price?

Not by itself. I price by stitch count, at $1.50 per thousand stitches with a $20 minimum. The thread weight is not a line on my quote.

The stitch count can change, though. If the digitizer raises the density for 60 weight, the file has more stitches. More stitches cost more at any per-thousand rate. Read the new count off the file before you quote. My guide on how to price machine embroidery walks through the math. My guide to estimating a stitch count covers it before you have the file.

Write the weight down with the colors

A reorder is easy when the record says the thread line and the weight next to each color number.

In Broidry, every spool in your thread drawer on the Supplies page has a Weight setting with 40wt, 60wt, or Other. Set it on any spool you own in more than one weight. Each design's page also has a notes box with a fill-in line for Needle. Put the 65/9 there on any design that runs a 60.

My guide to thread color records shows the rest of what goes in a finished-piece record.

The short version

Thread weight is kilometers per kilogram, so a bigger number is a thinner thread. Use 40 weight for almost everything. Switch to 60 weight for letters under about a quarter inch tall, down to about 4 millimeters, and for fine detail. Use 40 for the fills and 60 for the small text in the same design. Pair 60 weight with a 65/9 or 70/10 needle and slow the machine down slightly. Stitch a test, because the file may need more density. Keep a 60 or 90 weight bobbin under it. Write the weight down next to the color number.

Run your whole shop from one place.

Broidry tracks every order, quote, and payment in one place. Broidry is free until your first sale, with no credit card to start.